USA AISI C1045 ASTM A29/A29M - 91 1045 SAE 1045 UNS G 10450 Chemical Composition Min. % Max. % Carbon 0.43 0.50 Silicon 0.10 0.35 Manganese 0.60 0.90 Typical Mechanical Properties - Hot Rolled Condition Tensile Strength Mpa Yield Strength Mpa Elongation In 50mm % Hardness Brinell HB 570 - 700 300 - 450 14 - 30 170 - 210
1045 MEDIUM TENSILE CARBON STEEL BAR 1045 is a medium tensile low hardenability carbon steel generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 - 700 Mpa and Brinell hardness range 170 - 210 in either 1045 Steel vs. 1018 Steel Home Guides SF Gate1045 Steel 1045 is a medium-carbon steel, made with 0.45% carbon. Medium-carbon steels are stronger than low-carbon steels, but not as easy to weld, and can be tempered by quenching.
0.75-1.00%. Phosphorus, P (max) 0.04%. 0.035%. Sulfur, S (max) 0.05%. 0.040%. The carbon content of both 1045 and 4140 determines the last two digits of their grade number. The carbon content of 1040 steel is 0.40%, while 1045 has a carbon content of 0.45%. A comparison of bending-fatigue properties of surface A trend of increased endurance limit with a decrease in the degree of tempering was established for 1045 steel, but not for 10V45 steel. The least-tempered 4-min/220- o C condition of 1045 steel exhibited an unexpectedly high endurance limit of 605 MPa, a result ascribed largely to the higher surface residual stress for this condition.
AISI 1045 Steel Round Bar Sheet Plate, JIS S45C, DIN C45. AISI 1045 steel is high-quality medium-carbon steel with high strength. It also can be called JIS S45C and DIN C45 steel. It is usually used in normalized condition because of its bad hardenability. It needs to be quenching and tempering treatment to get higher mechanical performance. AISI 1045 Steel Double Eagle AlloysAISI 1045 is a medium carbon steel containing approximately 0.45% carbon that can be hardened by heat treatment to a maximum surface hardness of approximately Rockwell C 54-60 after flame or induction hardening.
AISI 1045 Steel, cold drawn, high temperature stress relieved, 50-75 mm (2-3 in) round Categories:Metal; Ferrous Metal; Carbon Steel; AISI 1000 Series Steel; Medium Carbon Steel. Material Notes:Respond to heat treatment, and flame and induction hardening, but not recommended for carburizing or cyaniding. AISI 4140 Alloy Steel (UNS G41400) - AZoMAISI 4140 alloy steel can be welded using all conventional techniques. However, the mechanical properties of this steel will be affected if it is welded in the heat-treated condition, and post-weld heat treatment should be performed. Heat Treatment. AISI 4140 alloy steel is heated at 845°C (1550°F) followed by quenching in oil.
AISI SAE ASTM 1018 steel has many semifinished and final products such as round bar, flat bar, steel tubing and pipes, etc. 1018 carbon steel is versatile and is commonly used in a variety of carburized parts such as gears, pinions, ratchets, worms, pins, chain pins, pins, machine parts, tools and mold components. Atlas 1045 Medium Tensile Carbon Steel Bar 1045Medium Tensile Carbon Steel Bar 1045 Colour code:Jade Green Introduction Atlas 1045 is a fully killed plain carbon steel product containing nominally 0.45% carbon. This grade was formerly designated as K1045. Atlas 1045 is supplied based on it meeting specified chemical composition requirements only. Related Specifications
SAE AISI 4140 Alloy Steel. SAE 4140 (AISI 4140 steel) is a Cr-Mo series (Chrome molybdenum series) low alloy steel, this material has high strength and hardenability, good toughness, small deformation during quenching, high creep strength and long-lasting strength at high temperature. 4140 Steel Uses. AISI SAE 4140 alloy steel can be made into round steel bar, flat & square steel bar, steel SAE-AISI 1045 (S45C, G10450) Carbon Steel ::SAE-AISI 1045 steel is a carbon (non-alloy) steel formulated for primary forming into wrought products. 1045 is the designation in both the SAE and AISI systems for this material. G10450 is the UNS number. It can have a moderately high tensile strength among the wrought carbon or non-alloy steels in the database.
AISI 304 Grade Stainless Steel (UNS S30400) AISI 304 stainless steel (UNS S30400) is the most commonly used material in stainless steels, and is usually purchased in an annealed or cold worked state. Because SS 304 contains 18% chromium (Cr) and 8% nickel (Ni), its also known as 18/8 stainless steel.Type 304 has good processability, weldability, corrosion resistance, heat 1045 Medium Tensile Carbon Steel Bar Interlloy 1045 Medium Tensile Carbon Steel Bar. 1045 is a medium tensile low hardenability carbon steel generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 - 700 Mpa and Brinell hardness range 170 - 210 in either condition.Characterised by fairly good strength and impact properties, plus good machinability